全 3044 件が検索されました。（701 - 720件を表示）
- マニュアル
... damage. ●Alert statements ■EFFECTS OF SURROUNDING METAL ■EXTERNAL DIMENSIONS When mounting the proximity switch in a metal panel, maintain the clearances given in table 2. When installing it with the nut, the value is different depending on the kind of the nut used, ...
- マニュアル
...) Size Model M12 X3□12 M18 X7□18 M30 X12□30 A B 40 35 65 60 110 100 X2 Vs Load (1) Do not install the product in the following locations. Doing so may result in product failure or malfunction. ①Outdoor locations directly subject to sunlight, rain, snow, water droplets, or oil. ②Locations subject to atmospheres with chemical vapors, in particular solvents and acids. ③Locations subject to corrosive gases. (2) The Sensor may malfunction if used near ultrasonic cleaning equipment, high-frequency equipment, transceivers, cellular phones, inverters, or other devices that generate a high-frequency electric field. Please ...
- マニュアル
...,replace the sensor. Not Blinking Inconsistency has occurred on Lighting the settings (service data) written in by the IO-Link communications. Rated sensing distance （％） Precautions for Correct Use (1) Do not install the product in the following locations. Doing ...
- マニュアル
... of at least 0.3 mm2 for extension. · Do not apply the forces on the cord exceeding the following limits: Pull: 29.4N; torque: 0.1N·m; pressure: 20N; bending: 29.4N · Always keep the protective cover in place when using the product. Not doing ...
- マニュアル
... environments Tighten the screw such as vibration, use an End Plate even with a single amplifier while pressing the End Plate. unit. If mounting the product without joining the amplifier unit, seal the side optical communication part with lightproof tape. Fix the connector part ...
- マニュアル
... the power supply. (6) Dispose of this product as industrial waste. The Sensor can be used by only switching the sensing direction in five ways without changing the mounting hole of the Sensor. (1) Do not install the product in the following locations. Doing ...
- マニュアル
.... (6) When turning on the power by influence of temperature environment,an output mis-pulse sometimes occurs. After the sensor has passed for 300 msec after turning on, please use in the stable state. (7) The sensor is adjusted with a high degree of accuracy, ...
- マニュアル
... polarity of the power is correct, and do not connect to an AC power supply. • Do not short-circuit the load for the open collector output. • Do not lay the power supply cable for the Smart Sensor together with high-voltage lines or power lines. Doing ...
- マニュアル
..., Y and Z directions Operating pressure range 0 to 0.6 MPa Material ZDC2 Ni plating Applicable sensor E3AS-F, E3AS-L, E3AS-HL, E3Z, E3ZR, E3ZM Contents Material Air discharge The length of the sensor mounting screw is limited ...
- マニュアル
...sheet at your disposal. ２．Hold and screw the protective cover against the E3AS-HL reference plane. Reference plane * 5 6 3 0 5 4 7 - 0 A * © OMRON Corporation 2020 All Rights Reserved. The length of the sensor mounting screw is limited ...
- マニュアル
... pas directement dans la lumière sortante. Attention-L utilisation des commandes ou réglages ou l exécution des procédures autres que celles spécifiées dans les présentes exigences peuvent étre la cause d une exposition à un rayonnement dangereux. Do not disassemble this product. Doing ...
- マニュアル
.... Ne regardez pas directement dans la lumière sortante. Attention-L’utilisation des commandes ou réglages ou l’exécution des procédures autres que celles spécifiées dans les présentes exigences peuvent étre la cause d’une exposition à un rayonnement dangereux. Do not disassemble this product.Doing ...
- マニュアル
... regardez pas directement dans la lumière sortante. Attention-L utilisation des commandes ou réglages ou l exécution des procédures autres que celles spécifiées dans les présentes exigences peuvent étre la cause d une exposition à un rayonnement dangereux. Do not disassemble this product.Doing ...
- マニュアル
... from the power lines, or otherwise shielded. •Do not use the product in direct sunlight. •Do not use the product where humidity is high and dew condensation may occur. •Do not use the product where corrosive gases may exist. •If high-pressure washing water and ...
- マニュアル
... width, and must be of a consistent width to the back of the blade. Vinyl insulated round cable 2-1.8 dia. 4 cores (cross-sectional area of conductor: 0.15 mm2) Standard length 2 m .6 Do not disassemble the product. Doing ...
- マニュアル
...8.4 Laser Radiation is emitted from this aperture PEAK POWER 3000 μW PULSE DURATION 3 μs WAVE LENGTH 650 nm Operation lever (White) LD ON indicator .6 Do not disassemble this product. Doing so may cause exposure to the built-in light source which can damage eyes and skin. Never disassemble it. 5.3 8 LASER RADIATION DO NOT STARE INTO BEAM ■ Removing the Connector 2 R2 Fixer en continu la lumière sortante peut provoquer des troubles visuels. Ne pas fixer directement la lumière sortante. Attention-L’utilisation des commandes ou réglages ou l’exécution des procédures autres que ...
- マニュアル
... N; bending: 29.4 N Connecting Terminal · Do not apply excessive force such as tension, compression or torsion to the connector of the sensor head that is fixed to the amplifier unit. · Always keep the protective cover in place when using the product. Not doing ...
- マニュアル
... conductor: 0.15 mm2) Standard length 2 m CAUTION LABEL CERTIFICATION AND INDENTIFICATION LABEL PEAK POWER 3000 μW PULSE DURATION 3 μs WAVE LENGTH 650 nm ● Alert Statements / Messages d'alerte Do not disassemble this product. Doing ...
- マニュアル
...販売拠点は、Webページでご案内しています。 A x 2024年12月 Laser radiation is emitted from this aperture ● Meaning of Alert Symbols Do not disassemble this product. Doing so may cause exposure to the built-in light source which can damage eyes and skin. Never disassemble it. Ne pas démonter ce produit. Cela pourrait provoquer une exposition à la source lumineuse intégrée, qui peut endommager les yeux et la peau. Ne jamais le démonter. PRECAUTIONS FOR SAFE USE Please observe the following precautions for safe use of ...
- マニュアル
... Signal Words Indicates a potentially hazardous situation which, if CAUTION not avoided, may result in minor or moderate injury or in property damage. ●Alert statements CAUTION Do not attempt to take ant unit apart while the power is being supplied. Doing ...