検索結果

...ます。 （1）Do not use the product in excess of the rated voltage. Applying voltage beyond the rated voltage range may cause the product to break or burn. （2）Avoid wiring the product's cables parallel to power lines or high-voltage lines. Doing ...

... product. 4） Be sure to turn off the power supply before wiring. If the output line contacts the power supply line while the power is being supplied, the output circuit may be damaged. 5） Do not short-circuit the load. Doing ...

...) Large ST Model Setting up threshold value easily The device status can be identified at a glance by the color of the status indicator. 1-2 Input/Output Circuit Diagram PRECAUTIONS FOR SAFE USE The following items are necessary for ensuring safety, ...

... MODE 1-2 Input/Output Circuit Diagram Model in the RUN mode. The threshold value of the preset output 1 or output 2 can be changed. 2-3 Button Operation Table 27.50 Load The following items are necessary for ensuring safety, ...

... pressure range *The threshold value of output 2 is not changed. simultaneous long push Transit to tuning mode + simultaneous long push or Key lock is executed/released. + simultaneous long push *Refer to "Key lock" of ③ Useful Setting. + + Offset the displayed value ...

...4 to 20mA 0V 0100 . 0100 . 0700 . 0700 . OMRON OMRON OMRON OMRON OMRON MODE MODE MODE MODE MODE OUT1 °C °C Offset the displayed value so that the execution time pressure value becomes zero. This can be executed using the external input. ⇒Refer to [3] Output 2 Setting of ④ Detail Setting. OUT1 Mpa Mpa OUT1 0700 . 0123 . MODE finished. tune adj.0 *In the following cases, the product is not tuned but err tune is displayed. ・The execution time pressure value is larger than (maximum rated pressure value x 0.1). ・The execution time pressure value is equal to or ...

... of the rated voltage. Excess voltage may result in malfunction or fire. Never use the product with an AC power supply. Otherwise, explosion may result. PRECAUTIONS FOR SAFE USE The following precautions must be observed to ensure safe operation of the product. Doing ...

... 4 mm. ・Air suction draws the spindle in. ・If the spindle extrusion rate is high, the amplifier indication may display an error when a workpiece is contacted. ・Too much impact may shift the ball retainer inside the bearing, resulting in less operating range. If ...

... USE • Power Supply Voltage Do not exceed the voltage range indicated in the specifications. Applying a voltage exceeding the specifications or using an AC power supply may result in rupture or burning. • Faulty Wiring Do not reverse the power supply polarity. Doing ...

... USE • Power Supply Voltage Do not exceed the voltage range indicated in the specifications. Applying a voltage exceeding the specifications or using an AC power supply may result in rupture or burning. • Faulty Wiring Do not reverse the power supply polarity. Doing ...

... SAFE USE • Power Supply Voltage Do not exceed the voltage range indicated in the specifications. Applying a voltage exceeding the specifications or using an AC power supply may result in rupture or burning. • Faulty Wiring Do not reverse the power supply polarity. Doing ...

...%RH Ambient humidity ＊A pipe used for liquid detection should be 6 ∼ 13mm in outer diameter and 1mm thick with transparent material such as FEP, PFA, etc... The sensitivity selector switch should be kept at High in usual operation. With a small-diameter pipe (6mm or ...

... SAFE USE • Power Supply Voltage Do not exceed the voltage range indicated in the specifications. Applying a voltage exceeding the specifications or using an AC power supply may result in rupture or burning. • Faulty Wiring Do not reverse the power supply polarity. Doing ...

... USE • Power Supply Voltage Do not exceed the voltage range indicated in the specifications. Applying a voltage exceeding the specifications or using an AC power supply may result in rupture or burning. • Faulty Wiring Do not reverse the power supply polarity. Doing ...

...-SX, EE-SY) are built into the device being used and are, therefore, not equipped to deal with interference from an external light source. When using a Sensor without light modulation in an area exposed to an incandescent light or other external light interference, install ...

... Voltage Do not exceed the voltage range indicated in the specifications. Applying a voltage exceeding the specifications or using an AC power supply may result in rupture or burning. • Faulty Wiring Do not reverse the power supply polarity. Doing ...

... SAFE USE • Power Supply Voltage Do not exceed the voltage range indicated in the specifications. Applying a voltage exceeding the specifications or using an AC power supply may result in rupture or burning. • Faulty Wiring Do not reverse the power supply polarity. Doing ...

... manual CAUTION carefully before using the product. ●Warning Symbols CAUTION Provide safety measures in external circuits (i.e., not in the Temperature Controller) to ensure safety in the system if an abnormality occurs due to malfunction or due to external factors. Not doing ...

...生産以前(V1.2以下)） 電子温度調節器 取扱説明書（日/英/伊/独/仏/西語） ●Warning Symbols EJ1 Temperature controller EN Do not touch the terminals while power is being supplied. Doing so may occasionally result in minor injury due to electric shock. Instruction Manual Thank you for purchasing the OMRON Product. To ensure the safe application of the Product, only a professional with an understanding of electricity and electric devices must handle it. Read this manual carefully before using the Product and always keep it close at ...

... complies with the reinforced or double insulation standards specified in IEC 60664 for the EJ1 external power supply and for the power supply connected to the EJ1. 11) 12) 10) 13) Do not touch the terminals while power is being supplied. Doing ...