検索結果

... dangers of high-voltage equipment. S Precautions on touching the terminals of the product even after power has been turned OFF. (These terminals are live even with the power turned OFF.) 5. Do not perform withstand voltage or other megameter tests on the product. Doing ...

... AC Servomotors described in this manual are defined as looking at the end of the output shaft of the motor as follows: counterclockwise rotation is positive and clockwise rotation is negative. 7. Do not perform withstand-voltage or other megameter tests on the product. Doing ...

... in place as specified before using the product.  Consult your OMRON representative when using the product after a long period of storage. WARNING Always connect the frame ground terminals of the Servo Drive and the Servomotor to 100  or less. Not doing ...

... manual contains information you need to know to correctly use the Servo Drive and peripheral equipment. Before using the Servo Drive, read this manual and gain a full understanding of the information provided herein. After you finished reading the manual, keep it in a convenient place ...

... you need to know to correctly use the OMNUC G5 Series and peripheral equipment. Before using the OMNUC G5 Series, read through this manual and gain a full understanding of the information provided herein. After you finished reading the manual, keep it in a convenient place ...

... protection Install the latest commercial-quality antivirus software on the computer connected to the control system and maintain to keep the software up-to-date. Security measures to prevent unauthorized access Take the following measures to prevent unauthorized access to our products. • Install physical controls ...

... systems and facilities. Notice This manual contains information you need to know to use the DriveProgramming. Before using this product, read this manual and gain a full understanding of the information provided herein. After you finished reading this manual, keep it in a convenient place ...

... correctly use the CompoNet Communications Unit (Model: 3G3AX-MX2-CRT-E/3G3AX-RX-CRT-E). Before using the CompoNet Communications Unit, read this manual and gain a full understanding of the information provided herein. After you finished reading this manual, keep it in a convenient place ...

...The Risk Assessment for teaching an OMRON robot depends on the application. If the customer determines that teaching the robot in Manual Mode is allowable, the programmer may need to enter the robot workcell while High Power is enabled. Other programming methods can be used ...

... there are differences, such as in dimensions and work envelopes, the different models will be covered separately. Figure 1-1. eCobra 800 Robot By adding a SmartController EX or a PLC, the eCobra series robots replace the previous sCobra and Cobra ePLC series robots, ...

... to the robot and its power supply must be locked out and tagged out before any maintenance is performed. 14608-000 Rev. L Hornet 565 Robot User's Guide 21 2.3 Safety Precautions l The Hornet 565 must be well maintained, ...

...Refer to Materials and Finishes on page 20. P31 Platform (P/N 09503-xxx) The P31 platform has a rotation range of ±46.25°. The tool flange is machined into one of the pivot links. It does not rotate in relation to the pivot link, ...

.... Power to the robot and its power supply must be locked out and tagged out before any maintenance is performed. Viper 650/850 Robot with eMB-40/60R User's Guide 15 2.3 Safety Precautions l The Vipers must be well maintained, ...

... software on the computer connected to the control system and keep the software and virus definitions up-to-date. • Scan USB drives or other external storage devices before connecting them to control systems and equipment. Security measures to prevent unauthorized network access • Install physical controls ...

.... Locate the SD card compartment (see the preceding figure). 3. Carefully remove the SD card from the READ ME FIRST box or shipping container. 11069-000 Rev. H SmartController EX User's Guide 21 3.2 Connecting Power Position the card ...

... Units together and locking the sliders by moving them toward the back of the Units. The End Cover is connected in the same way to the Unit on the far right side of the Controller. A step in a procedure 1 Join the Units ...

... user is responsible for the safety of the AMR, which includes confirming that the system is stable with any payload, payload structure, or other attachments while functioning in the specified operating environment. Follow all unpacking safety instructions and use appropriate tools and equipment. Failure to do ...

... obstacles in its path, a low front laser in the bumper to detect obstacles lower than the safety scanning laser, and a rear-facing obstacle-detection laser, to ensure that it is safe for the transporter to back up or turn in place. For situations that are ...

...l A Touchscreen lets a user and an AMR communicate at the AMR's current location. Call/Door Boxes can be used either as call buttons, to allow a user at a remote location to request an AMR, as door boxes, to open an automated door ...

... localize a lost robot. Call Buttons and Door Boxes Call buttons issue a request for the AIV to go to the call button’s associated goal. Door Boxes act as remote I/O, and can issue requests to open closed doors equipped with a door activator ...