検索結果

.... 12x the conventional sensitivity 2.5x 10x the conventional inclination tolerance the conventional speed Measurement can be performed at a stable level in a large amount of ambient light, even on objects that do not reflect light ...

... maximum and minimum air volume and feedback time can be set to any desired values. Once a cleanliness threshold has been exceeded, the level of cleanliness can be increased in a short time by applying the maximum air volume. Constant feedback is provided ...

...combustion or rupture may occasionally result in serious injury. Do not disassemble, deform under pressure, heat to 100°C or higher, or incinerate the battery. CAUTION Do not use the Power Monitor in locations where flammable or explosive gases are present. Doing ...

... manuals for the right page. Previous displays LD ON LD ON LD ON LD ON 6 ZP-L display Required action as well as error displayed in multiple languages PATENT PENDING *1 ZP-L’s display supports four languages, ...

... not expose your eyes to the laser radiation either directly or indirectly (i.e., after reflection from a mirror or shiny surface). The laser radiation has a high power density and exposure may result in loss of sight. Do not disassemble the product. Doing ...

...) SUS 10 Cr Constant distance Cr ZS-HLDS5T Error (Pm) Measurement value (Pm) 10 With a CCD, the charge overflows to the next pixel when excessive light is received. This phenomenon does not occur with CMOS, ...

...use, turn OFF the power supply, and disconnect the power plug from the outlet. Contact your OMRON representative for repair of the product. Repairing it by yourself may cause danger. 9. Do not attempt to dismantle, repair, or modify the product. Doing ...

... the product, turn OFF the power supply, and disconnect the plug from the outlet. As repair by the customer is dangerous, contact an OMRON's local office or sales office. 9. Do not try to disassemble, repair, or modify the product. Doing ...

... wavelength information is converted to distance with a spectrometer ((4)), and the height is then measured. Unlike triangulation systems, as the emitted light and received light are positioned along the same axis, the measurement point remains the same at any position in the measuring range ...

... high. Environment Mutual Interference Model In order to ensure safe operation and maintenance, do not install the product in the vicinity of high-voltage devices or power equipment. ■ Wiring Do not use the product at voltages exceeding the rated values. Doing ...

...28 mm 10 μm 40 mm Controller (Dimensions  page 8) Appearance Power supply Output type Model NPN ZX-GTC11 PNP ZX-GTC41 DC Accessories (Order Separately) These are not included with the sensor and controller, ...

... the laser beam path is terminated during use. If a mirror or shiny surface is positioned in the laser beam path, ensure that the reflected beam path is also terminated. If the Unit must be used without terminating the laser beam path, position the laser beam path ...

.... • Use suitable torque and force when mounting the Sensor. After turning ON the power, allow the Smart Sensor to warm up for 15 minutes minimum prior to use. Measurements Do not expose the plunger to forces exceeding the limits in the following diagram. Doing ...

... expose your eyes to the laser radiation either directly or indirectly (i.e., after reflection from a mirror or shiny surface). Loss of sight may possibly occur in case of the exposure to laser high power density. Do not disassemble the product. Doing ...

...Loss of sight may possibly occur in case of the exposure to laser high power density. Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not disassemble the product. Doing ...

...Effective zero reset period Laser emission ON → OFF Laser emission OFF → ON 4 ms or more within 6 ms within 200 ms ON OFF Signal Laser emission reception OFF 4 Do not disassemble the product. Doing so may cause the laser beam to leak, resulting in the danger of visual impairment. Note: For Precautions for safe use and Precautions for correct use, refer to the Instruction Sheet supplied with the product. LD-OFF Input LD-OFF input Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser emission...

... necessary fine adjustments. Not Using a Mounting Bracket: Tilt the Sensor Head towards the workpiece as shown below. 79.4±0.05 48 Measurement center distance (43.85) workpiece (19.85) 10.5° ±0.1° Adjust the installation ...

... of an application that requires the entire measurement range Low-profile connector assembly height measurement Robot hand registration Visualization to prevent from stopping the production-line Laser life display function The end of the laser diode lifespan is automatically detected and displayed ...

... Communication Unit may come off during operation due to vibration. • If there is noise or other effects, install a ferrite core. When installing a ferrite core, do not allow the shield sheath to be caught between the communications connector and the cable. Not doing ...

... close at hand for future reference. Manual Name Cat. No. 3G3RX2 User’s Manual I620-E1 OMRON Corporation ©OMRON Corporation 2018 All Rights Reserved. ■Transporting, Installation and Wiring ・Do not drop or apply a strong impact on the product. Doing ...