検索結果

... require manually adding tools, drawing individual search regions, and configuring parameters, Learn All Codes handles these tasks automatically. This reduces the time needed to create complex jobs from minutes to seconds Result of Learn • Tools arranged in reading order • ROIs (Regions of Interest) ...

...: 120 ms Vibration settling time: 100 ms 20 x 20 = 400 chips per pallet Resonance frequency of pallet: 30 Hz Vision inspection Handling time per pallet: 220 ms per chip x 400 chips = 88 s Application The XY stage moves a pallet ...

... remove the two screws to mount the switch in any of the four possible orientations. If changing the direction of the head, pay attention to the orientation of the operation plunger. Roller Lever Bolt Set Position Marker Plate Set the indicator needle ...

...actuator) to increase resistance to oils, chemicals, and weather. Cables attached. Uses an airtight built-in switch. The case cover and box interior are molded from epoxy resin to increase the seal. The cover cannot be removed. The SC connector can be removed, ...

... colors correspond to the pin clamp numbers that are identical to the connector pin numbers. Insertion Pin Block Pin Clamp Key groove Key groove Key XS2C use XS2G use 6±0.5 • Tentatively insert the pins to the pin block holes ...

...humidity can cause bad connections and damage through corrosion, leading to degraded performance, therefore do not use these products in such environments. • Do not pull on the Connectors or cables with excessive force. • Do not step on or place any objects on the Connectors. Doing ...

.... Connector Connection and Disconnection • When connecting or disconnecting Connectors, be sure to hold the Connectors by hand. • Do not hold the cable when disconnecting Connectors. Use after confirming the direction of the polarity key groove. • Do not touch wiring with wet hands. Doing ...

...For 5 to 8-mm dia., just remove the tabbed, waterproof bushing. *A 5-mm dia. cable connects with or without the bushing. Anyone... Visual confirmation is possible. ...with no torque management The tightened ti position is clear, ...

.../O unit XW2K series For PLC Connection P.2 Flexibly achieve the smallest configuration by combining with common terminal blocks For PLC Connection • This product is the industry’s smallest*1 and is mountable in two ways (vertical and horizontal)*2, ...

...2 1 37 38 4 3 21 22 20 19 19 20 22 21 3 4 38 37 1 2 40 39 Triangular mark Note: Wire the connector terminals 1:1 so that the connector terminal numbers coincide. Cable length L (m) L 4 XW2R Models for Connection to OMRON PLCs with power supply terminals e-CON Type Ordering Information Appearance I/O Points Input/Output 16 Input Model Dimension A (mm) XW2R-N16GD-C1-COM 98.5 XW2R-N32GD-C1-COM 32 186.7 XW2R-N32GD-C2-COM Ratings and Specifications Power supply terminal block: 4 A/16 poles ...

...Precautions for Correct Use Wiring Precautions • Do not perform wiring work, remove connectors, or connect connectors while power is being supplied. Electric shock or damage to the device may result. • Double-check all wiring before turning ON the power supply. • After wiring, route the cable ...

...Precautions for Correct Use Wiring Precautions • Do not perform wiring work, remove connectors, or connect connectors while power is being supplied. Electric shock or damage to the device may result. • Double-check all wiring before turning ON the power supply. • After wiring, route the cable ...

... icing) *3 Note: This cable is for fixed parts. Do not use it for moving parts. *1. Contact resistance for the Connector. *2. Dielectric strength for the Connector. *3. However, when bending the cable to perform wiring, maintenance, and other work, do ...

...Precautions for Correct Use Wiring • Do not perform wiring work, remove connectors, or connect connectors while power is being supplied. Electric shock or damage to the device may result. • Double-check all wiring before turning ON the power supply. • After wiring, route the cable ...

...Precautions for Correct Use Wiring • Do not perform wiring work, remove connectors, or connect connectors while power is being supplied. Electric shock or damage to the device may result. • Double-check all wiring before turning ON the power supply. • After wiring, route the cable ...

... icing) *3 Note: This cable is for fixed parts. Do not use it for moving parts. *1. Contact resistance for the Connector. *2. Dielectric strength for the Connector. *3. However, when bending the cable to perform wiring, maintenance, and other work, do ...

... Required The retightening that is required for screw terminal blocks is not required for Push-in Plus terminal blocks. Your work load is reduced not only when wiring, but also for inspections, delivery (shipping), and maintenance. Safety The structure provides finger protection ...

... identify wiring. (Material: PA resin, blank) XW5@-P4.0-@ Note: 1. Different models are used for the top and side surfaces. 2. There is no place to mount the Top-surface Labels on Two-tier Terminal Blocks with a width of 3.5 mm, ...

... to 14 10 mm • Do not drop the Terminal Block. Terminal Block functionality may be inhibited. • Terminal Block is designed to satisfy the functions when mounting on the DIN Track. Always mount on the DIN Track. • Do not exceeds the ratings. Doing ...

... Cover) Shielded Models M30 Shielded Models Polyacetal resin M12 Unshielded Models M30 × 1.5 B C Applicable Sensor diameter [A Sputter Protective Covers cannot be used with a Capactive Proximity Sensor.] The cover uses Fluororesin, ...