検索結果

... with the RF Tag ID and turns ON BUSY. I: HS output will turn OFF when TRG turns OFF. J: When communications with RF Tag ends in an error, the ID Slave turns ON ERR (Error end) and 72_ERR (RF Tag missing error). ...

..., or between arguments. • A delimiter, which is determined according to the communication condition settings, is attached at the end of a command. ● Response format The non-procedural command response format is as follows: • In the event that a command is successfully executed: O ...

...Set any equation to perform addition/subtraction on the measurement result. The equation can be substituted with measurement results obtained by other tasks. Also, when using two Controllers in a gang-mount configuration, calculations can also be performed across channels. Allowable equation: ...

... in this instance is referred to as a node No. 58 Serial Communication ZG2-DSU User’s Manual Communication Commands Command/Response Format Command data Delimiter When processing ends successfully Response data O Delimiter ...

... set A is protected even when the monitoring zone is switched to zone set B before tEndZoneA. A simple measure is to modify separation distance (S) used when defining Zone set A such that it includes an additional component (Zextra) defined by the maximum approach speed (...

...1001 9 FE1(HT) EM ) 9 I Y i y 1010 10 FE2(LF) SUB * : J Z j z 1011 11 FE3(VT) ESC + ; K [ k { 1100 12 FE4(FF) IS4(FS) , < L \ l | 1101 13 FE5(CR) IS3(GS) - = M ] m } 1110 14 S0 IS2(RS) . > N ^ n ÅP 1111 15 S1 IS1(US) / ? O _ o DEL CIDRW System User’s Manual Undefined Undefined Undefined SECTION 6 Appendix Protective Construction IP- is governed by the test methods described below. Check in advance the seal characteristics under the actual environment and conditions of use. IP is the abbreviation of International ...

...1001 9 FE1(HT) EM ) 9 I Y i y 1010 10 FE2(LF) SUB * : J Z j z 1011 11 FE3(VT) ESC + ; K [ k { 1100 12 FE4(FF) IS4(FS) , < L \ l | 1101 13 FE5(CR) IS3(GS) - = M ] m } 1110 14 S0 IS2(RS) . > N ^ n ÅP 1111 15 S1 IS1(US) / ? O _ o DEL Undefined Undefined Undefined SECTION 7 ASCII Code Table 0000 CIDRW System User’s Manual 117 SECTION 7 Appendix Protective Construction IP- is governed by the test methods described below. Check in advance the seal characteristics under the actual environment and conditions of ...

...(For details on setting transition charts, see page 158.) Alphabet Display Format The alphabet appears on the main and sub-displays as shown in the following table. A B C D E F G H I J K L M N O P Q R S T U V W X Y Z INDEX SETTING TRANSITION CHARTS 20 Part Names and Functions ZX2 User’s Manual Button Operation The functions of buttons change according to the currently selected mode. CONTENTS Button type Button function RUN mode button Cursor buttons button button button MENU/SET button MENU mode • Normal press:...

... are output when the command is processed normally, and the command execution result is OK. A delimiter is inserted at the end of the response. The delimiter is always CR. Command Execution Result Parameter 1 0 CR Delimiter O ...

...BUSY 100 ms 100 ms NORM ERR Section 5 Timing Charts 72_ERR R-DATA Not defined. A B C Not defined. Not defined. D E F G H I J K A: The PLC turns ON INHIBIT and sends the execution command to the ID Slave. B: The ID Slave checks that INHIBIT is ON, determines the CMD (command), LEN (data length), and ADDR (start address), and then turns ON BUSY. C: The ID Slave starts communications with the RF Tag when one enters the Antenna's interrogation zone. D: The ID Slave turns ON the NORM signal when ...

... are output when the command is processed normally, and the command execution result is OK. A delimiter is inserted at the end of the response. The delimiter is always CR. Command Execution Result Parameter 1 0 CR Delimiter O ...

..._X*H_ [X*I One-shot duration: 30 ms _X*I_ V400-R2 series User’s Manual 87 Section 4 Setting Method Menu sheet One-shot duration: 40 ms Command [X*J _X*J_ [X*K One-shot duration: 50 ms _X*K_ [X*L One-shot duration: 60 ms _X*L_ [X*M One-shot duration: 70 ms Section 4 Menu Sheet/Command List 88 _X*M_ [X*N One-shot duration: 80 ms _X*N_ [X*O One-shot duration: 90 ms _X*O_ One-shot duration: 100 ms _X*P_ V400-R2 series User’s Manual [...

... duration: 30 ms [X*I _X*I_ 76 V500-R2 series User’s Manual Section 4 Setting Method Menu sheet One-shot duration: 40 ms Command [X*J _X*J_ One-shot duration: 50 ms [X*K _X*K_ [X*L One-shot duration: 60 ms _X*L_ One-shot duration: 70 ms [X*M One-shot duration: 80 ms Section 4 Menu Sheet/Command List _X*M_ [X*N _X*N_ [X*O One-shot duration: 90 ms _X*O_ One-shot duration: 100 ms [X*P _X*P_ V500-R2 series User’s Manual 77 Section 4...

... component are the same as for the output connections and input connections in tag data link communications respectively. Example: Getting the Number (0) of the Current Scene Send data (2 bytes): 0x53('S') 0x00  Receive data (5 bytes): 0x30('0') 0x00 0x4f('O') 0x4b('...

...1001 9 FE1(HT) EM ) 9 I Y i y 1010 10 FE2(LF) SUB * : J Z j z 1011 11 FE3(VT) ESC + ; K [ k { 1100 12 FE4(FF) IS4(FS) , < L \ l | 1101 13 FE5(CR) IS3(GS) - = M ] m } 1110 14 S0 IS2(RS) . > N ^ n − 1111 15 S1 IS1(US) / ? O _ o DEL CIDRW System User’s Manual Undefined Undefined Undefined SECTION 6 Appendix Protective Construction IP- is governed by the test methods described below. Check in advance the seal characteristics under the actual environment and conditions of use. IP is the abbreviation of International Protection....

...1001 9 FE1(HT) EM ) 9 I Y i y 1010 10 FE2(LF) SUB * : J Z j z 1011 11 FE3(VT) ESC + ; K [ k { 1100 12 FE4(FF) IS4(FS) , < L \ l | 1101 13 FE5(CR) IS3(GS) - = M ] m } 1110 14 S0 IS2(RS) . > N ^ n ÅP 1111 15 S1 IS1(US) / ? O _ o DEL Undefined Undefined Undefined SECTION 7 ASCII Code Table 0000 CIDRW System User’s Manual 129 SECTION 7 Appendix Protective Construction IP- is governed by the test methods described below. Check in advance the seal characteristics under the actual environment and conditions of ...

... V min./3 mA min. OFF voltage/OFF current *3 5 V max./1 mA max. 5 V max./1 mA max. ON delay 0.1 ms max. 0.1 ms max. 0.1 ms max. 0.1 ms max. 3.3 kΩ + COM_IN1/2/3 Internal circuit Internal circuit + Input terminals 3.3 ...

... unit data setting command Change the setting data of the processing unit. D CR S ↑ Space ↑ Unit number ↑ Space ↑ Data number ↑ Space ↑ Setting value (N letter) Normal processing O ...

... ! S D 2 B R b X 2 ” E D C S c X 3 # 3 E D D T d T 4 $ 4 E N E U e Q K % 5 A S F V f K N & 6 B E L B B C S H N E T L M S F H B E M C C ↑ R ↓ S O → S I ← L C ’ ( ) * + , . / G H I J K L W X Y Z [ \ = M ] > N ^ ? O ─ 7 8 9 : ; < FH/FHV Series Vision System User’s Manual (Z365-E1) g h i j ...

... color: Yellow *2 Cable with Connectors on Both Ends (RJ45/RJ45) Rugged RJ45 plugs type *1 Wire Gauge and Number of Pairs: AWG22, 2-pair Cable Cable color: Light blue 1-10 OMRON Model 0.3 XS5W-T421-AMD-...