全 53875 件が検索されました。（2841 - 2860件を表示）
- マニュアル
...Introduction How to Use This Manual Page Format Describes the settings. 9,600*, 19,200, or 38,400 None*, odd, or even 77 bits or 8 bits* 1sbit* or 2 bits None*, 02
, or 1B * ETX, 0A LF, 0D CR... - マニュアル
...The format of non-procedural commands are as follows: Example: A command to acquire a measured value MEASURE command * Each character is output as an ASCII code (except for FLOWDATA response). M E A S U R E O ...
- マニュアル
... is 5 times per minute or higher. Countermeasure Examples When switching an inductive load, connect an surge protector, diodes, etc., in parallel with the load or contact as shown below. Circuit Current C R Power supply Inductive load ...
- マニュアル
... command line I/F. Command frame has a Command Code area to control the R/W and Command Data area that is used with Command Code. Terminator that indicates the end of the frame is [LF]. RS-232C requires a start code [SOH], check data, and [...
- マニュアル
... " OMRON" to the ID Controller with controller number 2. Command Controller No. @ 0 2 T S FCS Test data Command code O M R O N 1 Terminator 4 * CR 2 5 2 2 Command code Test data FCS Terminator 3 Response Controller No. @ 0 3 58 RFID System Operation Manual 2 T S 2 O M R 5 O N 1 4 2 * ...
- マニュアル
...PARITY OFF OFF, ODD, EVEN p.104 p.104 STOP BIT 1 1, 2 p.104 BAUDRATE 38400 9600, 19200, 38400, 57600, 115200 p.104 NODE 0 0 to 16 DELMIT CR CR, LF, CR+LF p.104 p.104 WHITE BALANCE - - p.102 ALL CLEAR - - p.102 MEAS CLEAR - - p.103 LANGUAGE - ENGLISH, JAPANESE p.103 VERSION - - p.103 MODE SWITCH LOCK OFF LOCK OFF, LOCK ON p.107 KEY LOCK OFF LOCK OFF, LOCK ON p.107 TEACH IN LOCK OFF LOCK OFF, LOCK ON p.107 PASS NUMBER 0000 0~9999 p.107 OUTPUT (*8) EACH ALL, ...
- マニュアル
...Details Input Set the basic input format items. Output Set the basic output format items. None*/STX/ESC Select the symbol that indicates the beginning (header) of the command format. No symbol will be selected if [None] is selected. Suffix ...
- マニュアル
.... For a description of each command, refer to "List of Non-procedural Commands." •SYSGET/DATAGET/BANKGET command The returned value consists of left-aligned characters indicating the acquired value and a delimiter. Example: The returned value is -30 mm. - 3 0 ...
- マニュアル
...) are available for extending the installation distance between the Sensor and the Controller. Digital equalizer ZG-XEQ Cable for Sensor : 0.5 m (2 m) (flexible cable) ZG User’s Manual Digital equalizer ZG-XEQ Extension cable ZG-XC__...
- マニュアル
...The following values can be output when expressions are set. Item Description Message Judgment result The judgment result is output. (0:OK, -1:NG, -2: not measured) Judge (JG) Correlation The degree of match between the measurement image and model Correlation (...
- マニュアル
... USB interface. Synchronization method Start-stop Transmission code ASCII (Binary format can be selected only when outputting measurement values set at [Setup] - [Support] - [Calculation] - [Data].) Communication speed USB2.0-compliant Data length - Parity - Stop bit - Delimiter ...
- マニュアル
.... Section 4 Creating Setting Files Using the 2DCR Configear ■ Open 9,600*, 19,200, or 38,400 None*, odd, or even * 77 bits or 8 bits 1sbit* or 2 bits None*, 02
, or 1B * ETX, 0A LF, 0D CR , or 0D0A ... - マニュアル
...-RX40_UM_E.book 70 ページ ２００９年１２月１１日 金曜日 午前１０時５８分 (5) Interface settings This menu is used to specify conditions for PC connection. Settings Selections available New Line code CR...
- マニュアル
... the data retention time *1. High temperatures are those exceeding 125°C up to 250°C. • Resetting the data retention time
1.Reading data from the RF tag addresses 0010Hex to 0015Hex. Command : RDSTH100100006*[... - マニュアル
...The following values can be output when expressions are set. Item Description Message Judgment result The judgment result is output. (0:OK, -1:NG, -2: not measured) Judge (JG) Correlation The degree of match between the measurement image and model Correlation (...
- マニュアル
... USB interface. Synchronization method Start-stop Transmission code ASCII (Binary format can be selected only when outputting measurement values set at [Setup] - [Support] - [Calculation] - [Data].) Communication speed USB2.0-compliant Data length - Parity - Stop bit - Delimiter ...
- マニュアル
...Setting content Command 9600 bps (Factory default setting) Data length 8 bits (Factory default setting) Parity None (Factory default setting) Stop bit 1 bit (Factory default setting) Header None (Factory default setting) Footer ...
- マニュアル
... switches with ENTER key. 3 Selections available USB ID 0 to 9 IP Address 0 to 255. 0 to 255. 0 to 255. 0 to 255 Detailed Settings New Line Code SETTINGS AND MEASUREMENT Setting CR+LF, LF, CR USB ID 0 to 9 IP Address 0 to 255. 0 to 255. 0 to 255. 0 to 255 Subnet Mask 0 to 255. 0 to 255. 0 to 255. 0 to 255 Port Number 1024 to 65535 Gateway 0 to 255. 0 to 255. 0 to 255. 0 to 255 DNS Address 0 to 255. 0 to 255. 0 ...
- マニュアル
...[8] [OFF] Odd Even Adjust to the PC communication specifications. [1 ] 2 Xon/Xoff Flow control is performed with software. Data is sent according to the Xon/Xoff codes from external devices. ● ● ● Timeout [s] [...
- マニュアル
.... 1. 50 In the "Model parameter" area, select the search mode, then specify a value for each item for Search FZ3 Processing Items List Manual that mode. 2 Set value [factory default] Measurement Setting item Description [...